AUX E&H Series Instruções de Operação Página 77
- Página / 92
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
8.6 Corrective maintenance of measuring system
8.6.1 pH/redox transmitter
Cleaning the front panel
To clean the front panel, only use standard
cleaning agents.
The front panel is resistant to the following
cleaning agents (acc. to test methode
DIN 42 115):
• Isopropanol
• Thinned acids (3 %)
• Thinned alkalis (5 %)
• Ester
• Hydrocarbons
• Ketone
• Household cleaners
Caution!
Do not use any concentrated mineral
acids or alkalis, benzyl-alcohol,
methylene chloride or high-pressure
water vapour at over 100 °C.
8.6.2 pH/mV electrodes
Clean soilings on the glass electrodes as
follows:
•
Clean oily and greasy coatings
Clean with detergent (fat solvent,
e.g. alcohol, acetone, poss. detergent).
Warning:
Hands, eyes and clothes are to be
protected when using the cleaning
agents described below.
•
Limestone deposits or metal hydroxide
coatings
Loosen coatings with diluted hydrochlorid
acid (3 %), then rinse thoroughly.
•
Coatings containing sulphide (from flue
gas desulphurising plants or sewage
treatment plants)
Use mixture of hydrochlorid acid (0.5 %)
and thiourea (8 %), then rinse thoroughly.
•
Coatings containing protein (food industry)
Use mixture of hydrochlorid acid (0.5 %)
and pepsin (1 %), then rinse thoroughly.
Blocked diaphragms can under certain
circumstances be mechanically cleaned
(does not apply for teflon diaphragms and
open ring junction electrodes):
• Use a small key file
• File in one direction only
Air bubbles in the electrode
• Air bubbles may indicate an assembly
problem; check installation position
• The range from 15° to 165° from the
horizontal is permissible
• Horizontal installation or installation with the
plug-in head pointing down is not allowed
Redox electrodes
Careful mechanical cleaning of coated metal
pins or surfaces is possible.
8.6.3 Assembly
Please refer to the operating instructions for
the assembly in question for maintenance and
troubleshooting instructions. The operating
instructions also include instructions for
assembly and dismantling, sensor and gasket
replacement as well as information on
resistance, spare parts and accessories.
8.6.4 Liquid KCl supply
• KCI must flow without bubbles.
Unpressurised version: cotton thread
present?
• For counterpressure: pressure in KCl
reservoir must exceed medium pressure
by at least 0.8 bar.
• KCl consumption should be low but
noticeable. Approx. 1 ... 10 ml per day is
typical.
• Refill opening of sensors with KCI refill
opening on glass shaft must be open.
>15° >15°
PM253E08.CHP
Liquisys M CPM 223 / 253 Diagnosis and corrective maintenance
Endress+Hauser 75
- Endress Hauser 1
- Table of contents 3
- 1 General information 4
- 1.5 Product structure 5
- 2 Safety 6
- 2.5 Immunity to interference 7
- 2.6 Declaration of conformity 7
- 3 Installation 8
- 3.2 Dimensions 9
- 3.3 Mounting 10
- PM253E03.CHP 11
- 3.3.2 Mounting examples 12
- Endress+Hauser 11 13
- 3.4 Electrical connection 14
- 131094-4G 15
- Construction of special 16
- CPK1_12e.EPS 16
- Fig. 3.13 16
- • If the software setting 18
- Setpoint 19
- 4.3 Keys 20
- PM253ED4.CHP 21
- 4.5 Operating concept 22
- 4.5.2 Access codes 23
- 4.5.3 Menu structure 23
- • If a change is made but not 23
- • See the appendix of these 23
- 5 Instrument configuration 25
- RELAY2.CDR 26
- Oper.Mode 27
- Glass A5 28
- Fig. 5.4 29
- Alarm signalling and 29
- 28 Endress+Hauser 30
- PM253E5A.CHP 31
- Fig. 5.7 32
- User-defined current output 32
- Sel. Out2 33
- Tabelle (3) 34
- Table (3) 34
- 5.5 Monitoring functions 35
- Rel.Assg 36
- Curr.Assg 36
- CleanTrig 36
- 5.5.2 Check 37
- • Due to its semiconductor 37
- A.Thresh 38
- Err.Delay 38
- LowAlarm 38
- HighAlarm 39
- ProcMonit 39
- Tmax Low 39
- Tmax High 39
- GRENZ-E.CDR 40
- not allowed 41
- Pulse length modulation 42
- Pulse frequency modulation 42
- PM253E5B.CHP 43
- 5.6.4 ChemoClean function 44
- • Use relays 3 (water) and 44
- • When “Economy” is selected 44
- LC PV R2 45
- LC State 46
- 120 R239 48
- 0.3 R2310 48
- Clean = ChemoClean (5) 49
- Neutra controller (6) 49
- ChemoClean (5) 49
- Proc.Type 51
- 5.7 Service 52
- S.Default 53
- Contr E1 54
- SerNo E113 54
- LSG E114 54
- 5.10 Calibration 55
- the user is 55
- ≤ 0.05 and value 56
- 59.18 N2 59
- PV Offset 60
- 6 Interfaces 61
- Endress+Hauser 61 63
- 62 Endress+Hauser 64
- Endress+Hauser 63 65
- 64 Endress+Hauser 66
- Endress+Hauser 65 67
- 8.1 Diagnosis 68
- Endress+Hauser 67 69
- 223EXPHE.CDR 70
- 8.2.2 Disassembly of CPM 223 71
- 8.2.3 Assembly of CPM 223 71
- 8.2.4 Spare parts for CPM 223 72
- 253EXPHE.CDR 73
- 8.3.2 Disassembly of CPM 253 74
- 8.3.3 Assembly of CPM 253 74
- 8.3.4 Spare parts for CPM 253 75
- 8.4 Spare parts orders 76
- 8.6.1 pH/redox transmitter 77
- 8.6.2 pH/mV electrodes 77
- 8.6.3 Assembly 77
- 8.6.4 Liquid KCl supply 77
- 9 Accessories 79
- 10 Technical data 81
- 80 Endress+Hauser 82
- Endress+Hauser 81 83
- 11 Appendix 84
- Endress+Hauser 83 85
- 84 Endress+Hauser 86
- Endress+Hauser 85 87
- 12 Index 88
- PM253E12.CHP 89
- Declaration of contamination 91
- BA 194C/07/en/07.02 92
- Printed in Germany / CV5 / DT 92
Manuais e produtos relacionados com Aparelhos de ar condicionado "split system" AUX E&H Series
(15 páginas)
(19 páginas)
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais